×
Your cart is empty.
Contact us on 01283 763666
Email:sales@campercare.co.uk

Shop

Filter

Showing 1–24 of 87 results

View 12 24 All

Sort By
Please add widgets to the WooCommerce Filters widget area in Appearance > Widgets
  • 12 VOLT 12″ REPLACEMENT TUBE HYMER, BURSTNER, GERMAN (Copy)

    12 VOLT 12″ REPLACEMENT TUBE HYMER, BURSTNER, GERMAN (Copy)

    12 VOLT 12″ REPLACEMENT TUBE HYMER, BURSTNER, GERMAN (Copy)

    REPLACEMENT FLUORESCENT TUBE 12 VOLT, DAY WHITE HYMER, BURSTNER, GEIST, NEISMANN BISHOFF ( HYMER GROUP ) THIS 12 VOLT LED TUBE IS DESIGNED TO REPLACE YOUR EXISTING 12VOLT 12" FLUORESCENT WITH THAT OF OUR SUPA BRIGHT SMD LED VERSION. A CONVENTIONAL 12" FLUORESCENT BULB USES 11 WATTS OF POWER, OUR NEW LED TUBE CONSUMES JUST 2 WATTS AND GIVES OUT APPROXIMATELY TWICE THE AMOUNT OF LIGHT. THIS REPLACEMENT TUBE HAS BEEN DESIGNED FOR MOTORHOMES, CARAVANS ETC OF GERMAN MANUFACTURE THAT USE HIGHER OUTPUT BALLAST UNITS AND ENABLES YOU TO RETAIN YOUR EXISTING FITTINGS BUT CONVERT THEM TO LOW POWER SMD LEDS. SIMPLE TO FIT BUT DOES REQUIRE SOME SIMPLE WIRING MODIFICATIONS INSIDE YOUR LAMP UNIT..... A SIMPLE DIY OPERATION! FULL INSTRUCTIONS INCLUDED. APPROX TWICE THE LIGHT OUTPUT OF A CONVENTIONAL T5F8 TUBE . USES APPROX 2 WATTS OF POWER. LENGTH OF TUBE END OF TIP TO END OF TIP - 12 INCHES.  Most German motorhomes & caravans of the Hymer group use a unique higher output ballast unit that is NOT compatible with our other listings for "NO MODIFICATION" Led tubes,the tube in this listing overcomes the high output problem. 
    £16.99
  • 12 VOLT 21″ REPLACEMENT TUBE HYMER, BURSTNER, GERMAN

    12 VOLT 21″ REPLACEMENT TUBE HYMER, BURSTNER, GERMAN

    12 VOLT 21″ REPLACEMENT TUBE HYMER, BURSTNER, GERMAN

    REPLACEMENT FLUORESCENT TUBE 12 VOLT, DAY WHITE HYMER, BURSTNER, GEIST, NEISMANN BISHOFF ( HYMER GROUP ) THIS 12 VOLT LED TUBE IS DESIGNED TO REPLACE YOUR EXISTING 12VOLT FLUORESCENT WITH THAT OF OUR SUPA BRIGHT SMD LED VERSION. A CONVENTIONAL 21" FLUORESCENT BULB USES 21 WATTS OF POWER, OUR NEW LED TUBE CONSUMES JUST 4.5 WATTS AND GIVES OUT APPROXIMATELY TWICE THE AMOUNT OF LIGHT. THIS REPLACEMENT TUBE HAS BEEN DESIGNED FOR MOTORHOMES, CARAVANS ETC OF GERMAN MANUFACTURE THAT USE HIGHER OUTPUT BALLAST UNITS AND ENABLES YOU TO RETAIN YOUR EXISTING FITTINGS BUT CONVERT THEM TO LOW POWER SMD LEDS. SIMPLE TO FIT BUT DOES REQUIRE SOME SIMPLE WIRING MODIFICATIONS INSIDE YOUR LAMP UNIT..... A SIMPLE DIY OPERATION! FULL INSTRUCTIONS INCLUDED. APPROX TWICE THE LIGHT OUTPUT OF A CONVENTIONAL T5F13 TUBE. USES APPROX 4.5 WATTS OF POWER. LENGTH OF TUBE END OF TIP TO END OF TIP - 21 INCHES. NOTE : THE LAMP UNIT IN THE PICTURE IS FOR PICTORIAL PURPOSES ONLY. YOU ARE PURCHASING THE LED TUBE ONLY. Most German motorhomes & caravans of the Hymer group use a unique higher output ballast unit that is NOT compatible with our other listings for "NO MODIFICATION" Led tubes,the tube in this listing overcomes the high output problem. 
    £21.99
  • 2002 – 2006 BONNET PROTECTOR

    2002 – 2006 BONNET PROTECTOR

    2002 – 2006 BONNET PROTECTOR

    BONNET PROTECTOR DUCATO, BOXER, RELAY 2002 - 2006.

    SUITABLE FOR 2002 - 2006 Motorhomes, Vans, Pickups etc

    NOT ONLY GIVES FANTASTIC BONNET PROTECTION FROM STONECHIPS, ROAD TAR, SUN, HAIL AND ALL OTHER ENVIROMENTAL ELEMENTS...... BUT THEY LOOK SUPERB !!

    AVAILABLE IN BLACK ONLY

    PROTECT YOUR INVESTMENT, EASY & SIMPLE TO FIT USING ELASTIC STRAPS AND CLIPS ON THE UNDERSIDE OF THE BONNET, NEEDS NO TOOLS.

    MANUFACTURED FROM A TOUGH STRONG VINYL WITH A FLEECY LINING TO ABSORB IMPACTS, ESPECIALLY MANUFACTURED AND TAILORED TO FIT THE MODELS LISTED.

    £49.99
  • CARBON MONOXIDE ALARM… THE “SILENT” KILLER

    CARBON MONOXIDE ALARM… THE “SILENT” KILLER

    CARBON MONOXIDE ALARM… THE “SILENT” KILLER

    THE CAMPERCARE " SLEEP SAFE " CARBON MONOXIDE ALARM

    All gas appliances give off CARBON MONOXIDE, inside your Motorhome, Caravan, Boat RV etc are Gas Heaters, Cookers, Water Heaters etc that have the potential to emit harmful Carbon Monoxide fumes into the living area.

    Carbon Monoxide is ODOURLESS so you are unaware its present.

    Our simply to install CARBON MONOXIDE alarm continually monitors the surrounding air and alerts of danger with a piercing alarm as well as flashing LED light. The LCD display shows the PPM content in the air and can be checked at any time simply by pushing the button.

    Operates on 3 x AA batteries ( not supplied ) that will last for approx 12 months, the unit is simple to fit by just 2 screws ( supplied ).

    SLEEP SAFE..SLEEP SOUND.

    Dimensions - 10cm WIDE x 3.5cm DEEP

    £15.99
  • OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER BRUSHED STEEL COLOUR

    OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER BRUSHED STEEL COLOUR

    OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER BRUSHED STEEL COLOUR

    OEM (ORIGINAL MANUFACTURERS EQUIPMENT ), SUPERB RECESSED DOWNLIGHTER LAMP WITH CLEAR PERSPEX COVER

    NUMBER OF SMD : 1 CREE WARM WHITE

    LIGHT OUTPUT : 18 watts

    POWER CONSUMPTION : 1 Watt

    SWITCH : NO

    MOUNTING : RECESS ( 22mm D reqd )

    ROTATION : NO

    DIMENSIONS OF LAMPMAX W 70mm

    £25.99
  • OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER BRUSHED STEEL COLOUR (Copy)

    OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER BRUSHED STEEL COLOUR (Copy)

    OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER BRUSHED STEEL COLOUR (Copy)

    OEM (ORIGINAL MANUFACTURERS EQUIPMENT), SUPERB  LAMP WITH CLEAR PERSPEX COVER, BRUSHED STEEL COLOUR

    NUMBER OF SMD : 3 CREE WARM WHITE

    LIGHT OUTPUT : 28 watts

    POWER CONSUMPTION : 2 Watt

    SWITCH : YES

    MOUNTING : SURFACE

    ROTATION : NO

    DIMENSIONS OF LAMPMAX W 210mm D 38

    £32.99
  • OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER SILVER SAND

    OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER SILVER SAND

    OEM (ORIGINAL MANUFACTURERS) DOWNLIGHTER SILVER SAND

    OEM (ORIGINAL MANUFACTURERS EQUIPMENT), SUPERB RECESSED DOWNLIGHTER LAMP WITH CLEAR PERSPEX COVER

    NUMBER OF SMD : 1 CREE WARM WHITE

    LIGHT OUTPUT : 18 watts

    POWER CONSUMPTION : 1 Watt

    SWITCH : NO

    MOUNTING : RECESS ( 22mm D reqd )

    ROTATION : NO

    DIMENSIONS OF LAMPMAX W 70mm

    £25.99
  • REAR COLLISION PREVENTER LED FLASHER UNIT

    REAR COLLISION PREVENTER LED FLASHER UNIT

    REAR COLLISION PREVENTER LED FLASHER UNIT

    REAR COLLISION PREVENTER.

    A SUPERB SIMPLE DEVICE THAT INSTANTLY DRAWS ATTENTION TO FOLLOWING VEHICLES THAT YOU ARE STOPPING. EASY TO INSTALL.... THE SMALL UNIT  (4CM X 2.5CM X1CM) WIRES TO YOUR HIGH LEVEL LED BRAKE LAMP. WHEN YOU PUSH THE BRAKE PEDAL YOUR HIGH LEVEL BRAKE LAMP RAPID FLASHES FOR APPROX 5 FLASHES THEN REMAINS ON AS NORMAL .

    WIRING IS SIMPLE, THE SMALL PLASTIC BOX IS CONNECTED TO THE TWO WIRES LEADING TO YOUR HIGH LEVEL BRAKE LAMP.... AND THATS IT DONE!!

    HAS NO EFFECT ON CANBUS ELECTRICAL SYSTEMS

    £10.99
  • SHOWER BUDDY, SHOWER HEAD ON/OFF VALVE

    SHOWER BUDDY, SHOWER HEAD ON/OFF VALVE

    SHOWER BUDDY, SHOWER HEAD ON/OFF VALVE

    SHOWER BUDDY
    A SIMPLE INGENIOUS DEVICE THAT ALLOWS THE SHOWER HEAD TO BE SWITCHED ON / OFF WITHOUT HAVING TO ALTER HEAT SETTINGS ETC OR TOUCH THE TAPS.

    HOW MANY TIMES DO YOU WISH TO JUST SWITCH THE WATER FLOW OFF FROM THE SHOWER HEAD (ie when washing hair or the kids feet or washing the dog etc) WITHOUT HAVING TO SHUT OFF THE TAPS, WHICH USUALLY ALTERS THE HEAT SETTING AND ALSO STOP WASTING WATER?

    THE 'SHOWER BUDDY' SIMPLY FITS BETWEEN THE SHOWER HEAD AND THE SHOWER PIPE.

    STANDARD THREADS TO FIT ALL FLEXIBLE SHOWER PIPES.

    UNIVERSAL AND SIMPLE TO FIT, SIMPLY UNSCREW THE SHOWER HEAD FROM THE PIPE, SCREW IN THE 'SHOWER BUDDY' INTO THE PIPE AND REATTACH THE SHOWER HEAD.....ITS AS SIMPLE AS THAT.

    NOW WITH A PUSH OF THE BUTTON THE WATER FLOW WILL BE SHUT OFF OR TO A TRICKLE.

    NOT CHEAP PLASTIC...... THE SHOWER BUDDY IS A QUALITY UNIT MANUFACTURED IN  BRASS AND CHROMIUM PLATED, COMPLETE WITH ADDITIONAL RUBBER WASHER.

    Note: THE SHOWER HEAD IS NOT INCLUDED AND IS FOR PICTORIAL PURPOSES ONLY.

    ANOTHER CLEVER PRODUCT FROM CAMPERCARE / LEDBULBS4U

    £10.99
  • SS STAINLESS SPOTLAMP 12v 12smd

    SS STAINLESS SPOTLAMP 12v 12smd

    SS STAINLESS SPOTLAMP 12v 12smd

    BRUSHED STEEL SURFACE MOUNTED LED LAMP CW 12 SMD BULB

    Specifications.

    VOLTAGE : 8 - 30 VOLTS ( suitable for all 12 volt and 24 volt applications )

    NUMBER OF SMD : 12

    LIGHT OUTPUT : 25 watts

    POWER CONSUMPTION : 1.2 Watt

    SWITCH : YES

    MOUNTING : SURFACE

    ROTATION : 360 / 90 up/down

    DIMENSIONS OF LAMP : Max W BASE 60mm

    MAX H 100mm

    £20.99
  • SUNSPOT DRL ( Daytime Running Lights ) UNIVERSAL FITTING

    SUNSPOT DRL ( Daytime Running Lights ) UNIVERSAL FITTING

    SUNSPOT DRL ( Daytime Running Lights ) UNIVERSAL FITTING

    THE SIMPLEST KIT TO FIT. FITS ANY VEHICLE REGARDLESS OF MAKE, MODEL, OR AGE. CAR, VAN, BIKE ETC. 12 VOLT SYSTEM EACH STRIP MEASURES 9cm LONG x 2cm WIDE AND CONTAINS 3 x COB CHIPS PER STRIP USING JUST 4.5WATTS OF POWER.
    £49.99
  • SUPERCHARGER 50 / 95 AMP PETROL / LPG BATTERY CHARGER

    SUPERCHARGER 50 / 95 AMP PETROL / LPG BATTERY CHARGER

    SUPERCHARGER 50 / 95 AMP PETROL / LPG BATTERY CHARGER

    MANUFACTURED & DESIGNED BY US HERE IN THE UK.

    THE SUPERCHARGER IS A REVOLUTIONARY PORTABLE PETROL AND LPG GAS POWERED BATTERY CHARGER THAT HAS BEEN ESPECIALLY DEVELOPED FOR THE MOTORHOME, CARAVAN, BOAT, LEISURE AND MANY ' OFF GRID ' APPLICATIONS.

    UTILISING PROVEN AUTOMOTIVE ALTERNATOR TECHNOLOGY COMBINED WITH RUGGED SWITCHGEAR AND QUIET, POWERFUL AND LIGHTWEIGHT 4 STROKE ENGINES, THE SUPERCHARGER HAS PROVED TO BE AN AMAZING SUCCESS SINCE ITS LAUNCH IN 2012.

    AVAILABLE WITH EITHER 50 AMP or 95 AMP 12 VOLT FULLY REGULATED OUTPUT AND WITH STRAIGHT PETROL OR DUAL FUEL PETROL & LPG THERE IS A SUPERCHARGER TO SUIT EVERY REQUIREMENT.

    INTERESTED AND WANTING TO KNOW MORE ?

    CLICK THE  WEBSITE URL TO GO TO OUR SUPERCHARGER WEBSITE FOR FULL SPECIFICATIONS, PRICES, IMAGES AND MUCH, MUCH MORE !............. OR TYPE IN www.thesupercharger.co.uk INTO YOUR BROWSER.

  • Supercharger 50 AMP Battery Charger

    Supercharger 50 AMP Battery Charger

    Supercharger 50 AMP Battery Charger

    THE REVOLUTIONARY SUPERCHARGER 12 VOLT DC PETROL CHARGER IS HERE WEIGHS JUST 11.5 KGS. MEASURES JUST 45cm ( 17.5" ) Long   38cm ( 15" ) High   25cm ( 10" ) Wide SUPERLIGHT WEIGHT SUPER SMALL SUPER QUIET How to Use: The SUPERCHARGER has been developed for complete ease of use giving the user a portable and safe efficient method of recharging 12 volt batteries in the minimum time period. Automotive alternators have proved themselves over decades to be robust and reliable over thousands of miles. You cannot overcharge and damage a battery using the SUPERCHARGER as the in built charge controller only allows the maximum amount of current that the battery will accept safely. Operating the SUPERCHARGER is so easy.... 1, Connect the booster leads to the SUPERCHARGER unit FIRST then to the battery terminals RED + POSITIVE & BLACK - NEGATIVE *. Switch the power switch to ON and you will see the ammeter illuminate ( 50 AMP ONLY) or the RED charging light illuminate ( 95 AMP ) this checks the internal fuse etc are working correctly, SWITCH THE POWER SWITCH BACK TO THE OFF POSITION. 2, Set the engine switch to ON, switch on the fuel and close the choke on the engine, adjust the engine throttle to approximately 1/4 throttle. 3. Ensure the power switch on the control box is set to OFF. 3 Firmly and sharply pull the starter handle and allow the engine to run for a few seconds before returning the choke position to the open position. 4. Once running smoothly adjust the revs to approximately 2/3rds then switch the power switch to ON. ( Note the ammeter illumination should extinguish (50 amp) or the red charger lamp extinguish on the 95 amp. 5. The ammeter needle should move ( 50 amp only ) and the engine revs drop as the alternator produces power and comes under load. 6. Adjust the engine throttle to reduce the revs to a position that the engine operates smoothly and as quietly as possible. 7. The SUPERCHARGER is now charging your battery, the SUPERCHARGER will monitor your battery condition and put in the maximum number of amps that your battery requires. 8. When finished switch off, disconnect the leads and put the SUPERCHARGER away for next time. * THE ABOVE IS NOT INTENDED AS AN IN DEPTH OPERATING GUIDE, FULL COMPREHENSIVE INSTRUCTIONS AND HEALTH AND SAFETY INFORMATION ACCOMPANYS THE SUPERCHARGER UNIT AND MUST BE ADHERED TO. In our accessory section you will find booster leads that do not require to be disconnected each time, they are fitted with a quick release mechanism that allows for swift hassle free connection. The SUPERCHARGER has been specifically designed with reliability and ease of use in mind, take for example the control box, this has been constructed to be rugged eliminating flimsy circuit boards, silicon chips etc that can easily fail, the SUPERCHARGER utilises proven heavy duty switch gear and instrumentation to give you complete peace of mind.
    £579.00
  • SUPERSUN DRL ( Daytime Running Lights ) THE BRIGHTEST AVAILABLE

    SUPERSUN DRL ( Daytime Running Lights ) THE BRIGHTEST AVAILABLE

    SUPERSUN DRL ( Daytime Running Lights ) THE BRIGHTEST AVAILABLE

    SUPERSUN UNIVERSAL DRL KIT... seeing is believing ! THE BRIGHTEST DRL KIT AVAILABLE.

    UNIVERSAL FITTING FOR DUCATO, RELAY, JUMPER, TRANSIT, MERCEDES, VW, RENAULT ETC WE GUARANTEE OUR PRODUCTS... IF YOU ARE NOT TOTALLY SATISFIED WITH THIS KIT WE WILL REFUND YOUR PURCHASE PRICE WITHOUT QUESTION.

    DO NOT CONFUSE OUR SET WHICH WE SOURCE AND ASSEMBLE OURSELVES WITH ANY OF THE OTHER INFERIOR SETS AVAILABLE. YOU WILL BE TOTALLY ASTONISHED BY HOW BRIGHT AND SIMPLE TO FIT OUR 'SUPERSUN' SET IS. KIT HAS EVERYTHING YOU NEED TO FIT. UNDOUBTEDLY THE BRIGHTEST DRL SET AVAILABLE, SIMPLE TO FIT, NO LARGE HOLES TO DRILL OR CUT OUT, CAN BE FITTED USING THE 'SUPER BOND' SELF ADHESIVE PADS ( SUPPLIED ) OR THE SCREW IN STUDS ( SUPPLIED ).

    FULLYWATERPROOF.

    COMES COMPLETE WITH SWITCH MODULE THAT AUTOMATICALLY SWITCHES THE LIGHTS ON/OFF WITH THE IGNITION AND COMPLIES WITH EU LEGISLATION TO SWITCH THE DRLs OFF WHEN THE HEADLAMPS ARE SWITCHED ON.

    CHECK OUT THE SPECIFICATIONS BELOW. MACHINED ALUMINIUM NOT CHEAP PLASTIC or STEEL. MAGNIFIED BULLS EYE LENS 55mm DIAMETER 25mm DEEP  (picture 2 ) 30MM  9w SUPER BRIGHT COB CHIP ... THE VERY LATEST LED CHIP. ( picture 3 & 4) FULLY WATERPROOF VOLTAGE REGULATED FOR LONG LIFE ( picture 5 ) EU CONFORMING SWITCH MODULE C/W WIRING HARNESS ( picture 6 ) PIGGY BACK FUSE SPUR ... SIMPLICITY TO INSTALL ( picture 7 ) BULLET CONNECTORS FOR CONVENIENCE SUPER BOND SELF ADHESIVE PADS & SCREW IN STUDS ( picture 8 ) FULL SIMPLE TO UNDERSTAND AND EASY TO FOLLOW STEP BY STEP INSTRUCTIONS. Wiring: RED to IGNITION live+ USING PIGGY BACK FUSED SPUR ( supplied ) BLACK to EARTH - WHITE to REAR OF HEADLAMP USING SPLICED CONNECTOR (supplied ) BULLET CONNECTOR LEADS TO DRL UNITS. ITS AS SIMPLE AS THAT!! SUPERSUN KIT COMPRISES 2 x  WATERPROOF MACHINED ALUMINIUM HIGHEST OUTPUT DRL LED LAMPS 2 x SUPERBOND SELF ADHESIVE PADS 2 x MACHINE STUD SCREWS C/W NUTS 1 x SWITCH MODULE (* With auto on/off when the headlamps are switched on ) complete with wiring loom. 1 x SPLICE CONNECTOR 1 x PIGGY BACK FUSED SPUR 1 x FULL SET INSTRUCTIONS * The AUTO on/off function can be disconnected to allow the DRL lamps to remain on. THESE REALLY ARE SIMPLE TO INSTALL, THE HIGH STRENGTH SELF ADHESIVE OR THE SCREW STUDS MAKE THESE TRULY A UNIVERSAL  DRL KIT. FOR MORE LED BULBS & LIGHTING SEE OUR OTHER LISTINGS AND SEE THE IMAGES ABOVE FOR CATALOGUE REFERENCE.
    £59.99
  • T5F13 REPLACEMENT LED TUBE 21″….. NO MODIFICATION REQUIRED EXCLUSIVE

    T5F13 REPLACEMENT LED TUBE 21″….. NO MODIFICATION REQUIRED EXCLUSIVE

    T5F13 REPLACEMENT LED TUBE 21″….. NO MODIFICATION REQUIRED EXCLUSIVE

    DIRECT REPLACEMENT FOR 21" FLUORESCENT TUBE

    NO MODIFICATION REQUIRED...WORKS WITH EXISTING BALLAST UNIT

    A STANDARD FLUORESCENT TUBE USES APPROX 2.5xTHE POWER CONSUMPTION

    Specifications. EXCLUSIVE TO US... DESIGNED AND MANUFACTURED TO OUR REQUIREMENTS.

    VOLTAGE : WORKS WITH 12 VOLT FLUORESCENT LAMPS...NOT SUITABLE FOR GERMAN HYMER GROUP ( HYMER, BURSTNER NEISMANN BISCHOFF, FLAIR, GEIST )

    NUMBER OF SMD : 60 day white

    LIGHT OUTPUT : 45 watts ( approx 1.5x the light output of a conventional fluorecent tube )

    POWER CONSUMPTION : 5.4 Watt

    DIMENSIONS : Max L 530mm 21" ( end of pin to end of pin )

    £21.00
  • T5F8 REPLACEMENT LED TUBE 12″….NO MODIFICATION REQUIRED EXCLUSIVE

    T5F8 REPLACEMENT LED TUBE 12″….NO MODIFICATION REQUIRED EXCLUSIVE

    T5F8 REPLACEMENT LED TUBE 12″….NO MODIFICATION REQUIRED EXCLUSIVE

    DIRECT REPLACEMENT FOR 12" FLUORESCENT TUBE

    NO MODIFICATION REQUIRED...WORKS WITH EXISTING BALLAST UNIT

    A STANDARD FLUORESCENT TUBE USES OVER 2.5 X THE POWER CONSUMPTION.

    Specifications. EXCLUSIVE TO US... DESIGNED AND MANUFACTURED TO OUR REQUIREMENTS.

    VOLTAGE : WORKS WITH 12 VOLT FLUORESCENT LAMPS...NOT SUITABLE FOR GERMAN HYMER GROUP ( HYMER, BURSTNER NEISMANN BISCHOFF, FLAIR, GEIST )

    NUMBER OF SMD : 30 day white

    LIGHT OUTPUT : 35 watts ( approx 1.5x the light output of a conventional flourescent tube )

    POWER CONSUMPTION : 3.5 Watt

    DIMENSIONS : Max L 300mm 12" ( end of pin to end of pin )

    £16.99
  • G4 6SMD HORIZONTAL

    G4 6SMD HORIZONTAL

    G4 6SMD HORIZONTAL

    DIRECT REPLACEMENT FOR THE 10 WATT G4 Bi PIN HORIZONTAL FITTING HALOGEN BULB

    Specifications.

    VOLTAGE : 8 - 30 VOLTS ( suitable for all 12 volt and 24 volt applications )

    NUMBER OF SMD : 6

    LIGHT OUTPUT : 18 watts

    POWER CONSUMPTION : 1 Watt

    DIMENSIONS : Max W 25mm

    £5.50
  • GU10 240 VOLT 60 smd

    GU10 240 VOLT 60 smd

    GU10 240 VOLT 60 smd

    DIRECT REPLACEMENT 240 VOLT GU10 DOWNLIGHTER BULB

     AVAILABLE IN COOL WHITE AND WARM WHITE - NON DIMMABLE

    Specifications.THIS IS THE MOST POPULAR REPLACEMENT BULB FOR 50 WATT HALOGEN BULBS IN KITCHENS BATHROOMS ETC

    VOLTAGE : 220 - 240 VOLT

    NUMBER OF SMD : 60

    LIGHT OUTPUT : 52 WATTS

    POWER CONSUMPTION : 4 Watt

    DIMMABLE : NO

    DIMENSIONS : Max W 50mm

    £4.49
  • LADDER GUARD / CLIMB STOPPER

    LADDER GUARD / CLIMB STOPPER

    LADDER GUARD / CLIMB STOPPER

    EXCLUSIVE TO US

    CLIMB STOPPER REAR LADDER GUARD. STOPS RISING CRIME

    THIS UNIVERSAL FITTING* UNIT IS DESIGNED TO DETER UNAUTHORISED PERSONS FROM SCALING THE REAR LADDER AND ACCESSING THE ROOF OF THE MOTORHOME.

    IT IS A SAD FACT THAT IN TODAYS SOCIETY MOTORHOMES ARE INCREASINGLY BEING TARGETED BY THIEVES DUE TO POSSESSIONS BEING LEFT INSIDE. WITH LARGER ROOFLIGHTS NOW BEING USED, ACCESS THROUGH THESE HAS BECOME EASIER. STOP UNWANTED CHILDREN CLIMBING ON TO THE ROOF, PROTECT TOP BOXES, PREVENT " GAS ATTACKS" ETC,ETC.

    THE CAMPERCARE "CLIMB STOPPER"LADDER GUARD IS SIMPLE TO FIT, SIMPLY HOOK OVER UPPER LADDER RUNG, ADJUST THE MIDDLE SLIDING BRACKET AND LOCK IN POSITION. ONCE ADJUSTED TO YOUR LADDER NO OTHER ADJUSTMENTS ARE NECESSARY. A VISIBLE DETERENT TO UNAUTHORISED PERSONS.

    SPECIFICATIONS. * Manufactured from tough, weatherproof, easy clean, white coated aluminium/sandwich board.

    light and strong Universal fitting. Heavy Duty Aluminium top rung hook Comes complete with stainless steel fittings. galvanized steel nuts and bolts.. Red reflective tape. Complete with padlock and 2 keys. Size: 95cm Long x 25cm Wide . *Fits ladders with rungs up to 35cm apart.Simple to remove (with key) when required, needs no additional resetting. No drilling or modification needed to the ladder.
    £49.99
  • SSG BRUSHED STEEL SPOT 12v  12SMD

    SSG BRUSHED STEEL SPOT 12v 12SMD

    SSG BRUSHED STEEL SPOT 12v 12SMD

    BRUSHED STEEL SURFACE MOUNTED LED LAMP C/W 12 SMD BULB

    Specifications.

    VOLTAGE : 8 - 30 VOLTS ( suitable for all 12 volt and 24 volt applications )

    NUMBER OF SMD : 12

    LIGHT OUTPUT : 25 watts

    POWER CONSUMPTION : 1.2 Watt

    SWITCH : YES

    MOUNTING : SURFACE

    ROTATION : 360 / 90 up/down

    DIMENSIONS OF LAMP : Max W BASE 60mm

    MAX H 100mm

    £20.99
  • BONNET STONE CHIP PROTECTOR BONNET BRA  2006 – 2014

    BONNET STONE CHIP PROTECTOR BONNET BRA 2006 – 2014

    BONNET STONE CHIP PROTECTOR BONNET BRA 2006 – 2014

    AVAILABLE IN BLACK ONLY

    VEHICLE MODEL :- FIAT DUCATO, PEUGEOT BOXER, CITROEN RELAY

    SUITABLE FOR 2006 - 2014 ( X250 ) Motorhomes, Vans, Pickups etc (NOT 2014 -  FACE LIFT)

    NOT ONLY GIVES FANTASTIC BONNET PROTECTION FROM STONECHIPS, ROAD TAR, SUN, HAIL AND ALL OTHER ENVIROMENTAL ELEMENTS...... BUT THEY LOOK SUPERB !!

    AVAILABLE IN 3 COLOURS, BLACK, WHITE & SILVER.

    PROTECT YOUR INVESTMENT, EASY & SIMPLE TO FIT USING ELASTIC STRAPS AND CLIPS ON THE UNDERSIDE OF THE BONNET, NEEDS NO TOOLS.

    MANUFACTURED FROM A TOUGH STRONG VINYL WITH A FLEECY LINING TO ABSORB IMPACTS, ESPECIALLY MANUFACTURED AND TAILORED TO FIT THE MODELS LISTED.

    £49.99
  • MICRO BRUSHED STEEL 12v 6smd

    MICRO BRUSHED STEEL 12v 6smd

    MICRO BRUSHED STEEL 12v 6smd

    BRUSHED STEEL SURFACE MOUNTED LED LAMP CW 12 SMD BULB

    Specifications.

    VOLTAGE : 8 - 30 VOLTS ( suitable for all 12 volt and 24 volt applications )

    NUMBER OF SMD : 6

    LIGHT OUTPUT : 18 watts

    POWER CONSUMPTION : 1 Watt

    SWITCH : YES

    MOUNTING : SURFACE

    ROTATION : 360 / 90 up/down

    DIMENSIONS OF LAMP : Max W BASE 40mm

    MAX H 100mm

    £19.99
  • CREE 1 BRUSHED 12v 1x SUPER CREE

    CREE 1 BRUSHED 12v 1x SUPER CREE

    CREE 1 BRUSHED 12v 1x SUPER CREE

    BRUSHED STEEL SURFACE MOUNTED LED LAMP CW 1x SUPER BRIGHT CREE BULB

    Specifications. VOLTAGE : 12 NUMBER OF SMD : 1 x SUPER CREE cool white LIGHT OUTPUT : 25 watts POWER CONSUMPTION : 1.2 Watt SWITCH : YES MOUNTING : SURFACE ROTATION : 360 / 90 up/down DIMENSIONS OF LAMP : Max W BASE 60mm MAX H 100mm
    £21.99
  • 240 VOLT GENERAL BULB 28smd

    240 VOLT GENERAL BULB 28smd

    240 VOLT GENERAL BULB 28smd

    DIRECT REPLACEMENT FOR BAYONET AND SCREW IN CANDLE BULBS

    DIRECT REPLACEMENT 240 VOLT CANDLE BULB.

    AVAILABLE IN B22 Bayonet, E27 Large Screw & E14 Small Screw

    Specifications. VOLTAGE : 220 - 240 VOLTS NUMBER OF SMD : 28 LIGHT OUTPUT : +/- 45 Watts POWER CONSUMPTION : 4 Watt DIMMABLE : NO DIMENSIONS : Max Height from contacts 125mm Max Width 40mm
    £4.89